Do You Need a New Flow Switch?

Posted on by

The flow switch is a vital part of your swimming pool system, but people often mistake issues with this switch for issues with the pump itself. A faulty flow switch can cause the salt system to not come on at all or to stay on for too long. Just keep in mind that it is far more likely that your switch is having a problem than your pump.

There are some simple ways to tell which part is the issue. If you have a timer on your pump, start by shutting it of so that the pump just kicks on as needed instead of at a certain time. By doing this you can make sure it is not the timer itself causing problems. The flow switch sends a signal to the salt system to come on. If the flow switch signal continuously displays ‘no flow’, and you are able to tell that there is sufficient water flow, the problem is in the switch.

Turbo Cell Cleaning Stand – Simple Steps in Cleaning a Cell

Posted on by

Saline pools achieve their salt level by electrolytic cells in their generators. Occasionally, these cells require cleaning so that they will perform like new again. A Turbo cell cleaning stand is made to fit a Turbo cell and cleaning it can be done through the steps below.

Manually, the cell will have to be removed for inspection. Flaky deposits and other scale formations will usually be found on the plates. Debris can pass through the filter after a long period of time and build up. Wash these deposits off easily with a hose. The cell can be cleaned or sanitized with a mixture of muriatic acid and water.

Put the acid solution in a plastic container, and remember to wear gloves. Fasten the turbo cell cleaning stand and place a container or rag underneath in case of spills. The cord should be positioned side down when you fill the cell with the muriatic acid solution. It should be filled to the top and set aside to soak for 15 minutes.

Afterwards, it can be washed off with water. You can buy your salt cell cleaning stand at poolguysupply.com along with other pool cleaning equipment. If you prefer a different brand of salt cell cleaning stand, they have many options to choose from. Remember to buy a cleaning stand based on its compatibility with your cell, not by price or brand alone.

Reminders When Installing a Pool Flow Switch

Posted on by

pool 1

A pool flow switch is important because it serves as a stopper for releasing chlorine in the pool. It is meant to control the flow of water in and out of the pool generator. Below are some reminders when installing flow switches.

Before installing a pool flow switch it is important to check for any damages to your existing equipment. Aside from possible dents, there should be markings on the port to indicate which side the water will flow into and out of. If you think the switch is ready to be installed, you should consider installing a filter first. This will prevent any debris from interfering with the flow.

When you install the switch, it should be positioned horizontally and level. Make sure that the inlet does not get blocked with PVC cement while you are cementing it in position. Whether you are using a salt or chlorine generator, the flow switch should be placed away from the generator so that it will not corrode easily.

For a much better water flow for the switch, you can buy Pentair filter cartridges. They are easy to install and clean. These Pentair filter cartridges and other accessories are available at the Pool Guy Supply website.

The Importance of A Balanced Salinity Level

Posted on by

For those who do not know it yet, there is a reason why it is so important to test the salinity level of your pool. Before anything, people should know that salt water systems turn salt into chlorine, not just salty water.

Chlorine is important for your pool because it acts as a disinfecting agent. This means that no germs or harmful bacteria will survive in the pool water. Unwanted bits of wastes will also be eliminated, creating a clean environment for swimming.

The reason why salt levels need to be checked is because if there is not enough salt, there is nothing to turn into chlorine. You can use a salt tester kit to be sure. An indicator would show if there is a low salt level in the pool water. Too much salt in the pool would be harmful for any materials underwater, which include stone decorations, tiles, a pool temperature sensor and filter gauges.

Salt is a corrosive element, it can damage steel or metal over time. If the salt level indicated in the salt tester is high, the life span of accessories in the pool will be shortened by a few months. Equipment like your pool temperature sensor will eventually need replacement at some point. When the time comes it is best to buy supplies from a pool supply company like poolguysupply.com, instead of a hardware store.

The Advantages of a Saline Pool

Posted on by

Recently, saline pools have become more preferred as opposed to chlorine pools. Many people say that a salt water pool system is more comfortable and feels gentle on the skin.

It’s believed to be safer, and why wouldn’t it be? There’s no chlorine or toxic chemicals involved, just salt and a salt tester for keeping the pool on an ideal pH level. Homeowners like salt water systems more because the generators are self-cleaning. There’s no need for constant care and it needs little attention as far as maintenance is concerned.

Besides the generator, the salt cells only need cleaning from time to time. If the cell gets clogged it can simply be cleaned using a cleaning stand. Although a salt water pool system is arguably more expensive than a chlorine system, it cuts more costs in the long run. A saline pool can pay for itself overtime and besides, chlorine is more expensive and requires more maintenance.

The cost of buying chlorine to last a month is enough to buy another set of salt cells at Pool Guy Supply. At our website you will find how affordable salt system parts are for your pool. Think of a salt tester as a long term investment, saline pools will save you from future expenses that chlorine pools can not.

What Your Pool’s Pressure Gauge is Telling You

Posted on by

A pool filter pressure gauge makes it possible to indicate an impending problem sooner. There is an ideal water pressure for swimming pools; if the gauge is not showing a figure close to this, there could be something wrong.

An extremely low pressure reading usually means that the water is obstructed from getting to the filter. Either there are not adequate water levels or the water flow is being blocked by leaves or other debris. It could be the baskets or vacuums that are generating a build-up. It’s also possible that the impeller is clogged or the skimmer door is stuck.

Unstable pressure readings mean there is not enough water to supply the pump. A high pressure reading in your pool filter pressure gauge can only mean one thing. The more the filter media is clogged up, the higher the reading will be. So if you get readings like that then it’s time to clean your filters. A closed valve to a return line will also cause an abnormally high pressure.

In case your gauge does break, you can get replacement parts as well as replacement pool filter cartridges from the online pool supply company, poolguysupply.com. Aside from replacement pool filter cartridges, they also have filter manifolds, flow switches, and other pool supplies that might be the cause of pressure problems in your pool.

Checking your Salt Cell first Before Replacement

Posted on by

Pool Guy 1

Salt systems are commonly used nowadays because of the fact that salt water is healthier than chlorine. There are times, however, when problems with salt cells and salt systems are encountered and require calibration.

It’s rare for salt systems to break down easily, but users sometimes experience inaccurate readings. Because of that, owners prefer systems by Aqua Rite. Salt system troubleshooting is a basic step in checking if your system is broken. Generally, the cells should be free of any build up, sometimes they cause false readings. If there is any, you should clean them and if not then you have to re-calibrate the cell.

When you turn off the power of your Aqua Rite salt system, troubleshooting can start while the pump is running. Switch it to auto and after 5-15 seconds you should hear a click. In order to recalibrate you need to press the diagnostic button 5 times after hearing the click.

There’s nothing to worry about if the reading settles on something that’s close to the troubleshooting results in your manual. If it’s showing an absurd reading, you might need to buy new salt cells or salt system. You could choose better brands at poolguysupply.com or see if they have a more reliable system. It might be time to purchase a new salt system for your pool.

Consider Effective Cleaning Equipment for Your Pool

Posted on by

People love swimming pools, and if given the money, anyone would jump at the chance to have one at home. What people usually forget is that most pools sometimes have systems fitted with salt cells which require cleaning. Before installing a pool in your own backyard, you might want to consider setting aside some money for buying cleaning equipment like a turbo cell cleaning stand.

When placed outdoors, swimming pools tend to gather up a lot of solid debris on their surface. A leaf rake or a small net would be handy, but the long pole becomes tiring to hold over time. You can spend less time skimming if you have an automatic surface skimmer attached to the pool’s rim. You will also have to get some filter replacements when the filter gets clogged with debris.

Swimming pools use salt systems for chlorine, right? Well, they need cleaning too. They only need cleaning every 3 months or so, but the manual task is such a hassle. A turbo cell cleaning stand would make that job easier. For a general idea on what other equipment you may need for salt cells and pool filters, you can visit Pool Guy Supply’s website. They have all types of pool supplies that you are sure to find useful.

Why Its Best to Clean your Salt System

Posted on by

If you are one of the many who owns an Aqua Rite Cell, then you know very well that it’s meant to clean itself. It’s a system for your pool that produces chlorine without increasing the salinity level. Aqua Rite has plates inside the salt cells which convert the salt water into chlorine. These are the parts that are most overworked in the system.

Although it’s meant to be self-cleaning, an Aqua Rite Salt system would work much better if the turbo cell is cleaned at least several times each year. Over time, the cells would have gathered an accumulation of mineral deposits and debris from the water. The cheapest and fastest way to dissolve build up is using a solution of water and muriatic acid. You can also use the same solution for cleaning the different replacement salt cells.

You might also find it useful to get other accessories from Pool Guy Supply. Cleaning will be an easier task with several of these useful tools.

Water Sensors – Achieving the Right Temperature

Posted on by

pool 1

Pool and Spa owners both have a common concern in keeping the right water temperature. Ideally, the surface shouldn’t be too hot or too cold. Even homeowners who have their own pool would enjoy a swim much better under perfect water conditions. It’s a good thing that pool supply stores now sell water temperature sensor gadgets that can easily be installed.

Installing a temperature sensor like the Pentair temperature sensor is the ideal solution because it saves the effort of having to personally test the water. Generally easy to use, sensors are simple devices that you can attach into the existing plumbing of the pool.

Reliable branded sensors, like the Pentair temperature sensors, are longer lasting and make accurate readings. You might find more water sensors online from websites like Pool Guy Supply. They have Pentair sensors and other pool supplies you might find handy for your pool needs.